← All guides · Updated 14 October 2026
How to Calculate Plaster Quantity for Walls and Ceilings
Plaster is one of the easiest materials to over- or under-order, because the quantity depends on thickness, and thickness depends on how straight the wall underneath is. This guide shows the method used by estimators and a worked example you can scale to any room.
Typical plaster thicknesses
| Surface | Usual thickness |
| Internal walls | 12 mm (½ inch) |
| External walls | 15–20 mm (⅝–¾ inch) |
| Ceilings | 6–10 mm (¼–⅜ inch) |
| Rough or uneven brickwork | Add a thicker first coat; average thickness can reach 18–25 mm |
Thickness is the single biggest lever on cost: moving from 12 mm to 18 mm increases material by 50%.
The formula
- Plaster area = wall length × height, minus doors and windows. Add the ceiling if it is also plastered.
- Wet volume = area × thickness (use consistent units).
- Dry volume = wet volume × 1.27 (some builders use up to 1.33).
- Cement = dry volume × 1 ÷ (1 + sand parts); sand = dry volume × sand parts ÷ (1 + sand parts).
- Convert cement into 50 kg bags using about 0.0347 m³ per bag.
The BuildCostMate Plaster Calculator uses a dry-volume factor of 1.33 and a fixed 12 mm thickness, so its answers are about 5% higher than the 1.27 hand calculation below. Both factors are in common use.
Worked example: 100 square feet at 12 mm, 1:4 mix
- Area = 100 sq ft = 9.29 m².
- Wet volume = 9.29 × 0.012 = 0.1115 m³.
- Dry volume = 0.1115 × 1.27 = 0.1416 m³.
- Cement = 0.1416 ÷ 5 = 0.0283 m³ = 40.8 kg = 0.82 bag.
- Sand = 0.1416 × 4 ÷ 5 = 0.1133 m³ = 4.0 cubic feet.
Scaling to a room: a 14 × 12 ft room with 10 ft walls has 520 sq ft of wall. Deduct a door (about 21 sq ft) and two windows (about 15 sq ft each) = 469 sq ft. That is 4.69 times the example, so about 3.9 bags of cement and 18.8 cubic feet of sand before wastage.
Wastage and practical allowances
- Add 5–10% for droppings, uneven walls and mixing waste. Rough brickwork can need more.
- Do not deduct small openings (under about 1 m²) if you want a safety margin; most estimators deduct only larger ones.
- Reveals (the returns around door and window openings) add area; include them for accuracy.
- Order sand in a single delivery where you can, so colour and fineness stay consistent across the walls.
Good plastering practice
- Wet the brickwork before plastering so it does not suck the water out of the mix.
- Use screed guides (dots and bands) to control thickness and flatness.
- Cure for several days with light spraying, particularly outdoors in hot weather.
The Plaster Calculator applies these steps, including openings and a custom thickness. For the mix ratios themselves, see the cement and sand ratio guide.
Frequently asked questions
How much cement do I need to plaster 1000 square feet?
At 12 mm and 1:4, about 8.2 bags of cement and 40 cubic feet of sand, before wastage. Thicker plaster scales the figure up in proportion.
Which mix is best for internal plaster?
1:5 or 1:6 is common indoors, while external plaster is usually 1:4 or richer, because it must resist weather.
Does ceiling plaster use the same formula?
Yes, but ceilings are usually thinner (6–10 mm), so use the real thickness in the calculation.
Related tools and guides
Plaster CalculatorCement and sand ratiosPaint quantity guideBrick Calculator
These guides give general estimating methods. Always follow your engineer's drawings, local codes and the instructions of the material supplier.